Heating & Cooling · Northeast
Cost to run a heat pump in District of Columbia
At District of Columbia’s average residential rate of 25.40¢ per kWh, a heat pump drawing 2400W for 10 hours a day costs about $111 a month. Change the numbers below to match how you actually use yours.
Winters in District of Columbia are cold enough that a heat pump will carry real load from late autumn through early spring, then sit idle for the rest of the year. Spreading the annual cost evenly across twelve months therefore flatters the summer months and understates the winter bill.
Quick answer
Based on 2400W at a 60% duty cycle (this equipment cycles on and off rather than drawing full power continuously) and 25.40¢/kWh, the District of Columbia average for May 2026.
Calculate your own cost
Everything is worked out in your browser. Your numbers are never sent to our server.
— per year
Why the cost differs in District of Columbia
District of Columbia has the 42nd cheapest residential electricity of the 51 US states and territories we track, at 25.40¢ per kWh against a national average of 18.44¢. That is +37.7% compared with the national figure. The District is an entirely urban service territory with no generation of its own, so every kilowatt-hour arrives over transmission and the cost profile is dominated by distribution and delivery charges rather than fuel. Retail choice is available. Dense building stock means a high share of apartments, where cooling load per household is lower than the national norm but heating is often electric.
For this appliance specifically, the difference works out to an extra $366 a year over what the same heat pump would cost at the national average rate. Run the identical appliance in Hawaii and it would cost $2,733 a year; in Idaho it would cost $649. That spread of $2,084 is entirely down to location.
At District of Columbia's rate this single heat pump accounts for roughly 50% of a typical household's entire annual electricity bill. It is not a rounding error on your statement - it is one of the largest single line items in it.
District of Columbia sits above the national average, so the running cost of this heat pump is modestly higher than a typical US household would pay. Usage habits still matter more than location at this rate level.
Because District of Columbia has retail supplier choice, the state average blends many different contracted rates. If you have shopped for a plan, your own price per kWh is the number to put in the calculator.
| Location | Rate | Per month | Per year |
|---|---|---|---|
| District of Columbia this page | 25.40¢ | $111 | $1,335 |
| US average | 18.44¢ | $80.83 | $969 |
| Idaho cheapest state | 12.35¢ | $54.13 | $649 |
| Hawaii most expensive | 52.00¢ | $228 | $2,733 |
District of Columbia electricity rate trend
Rates in District of Columbia have moved from 22.70¢ to 25.40¢ per kWh over the last twelve months of published data. Nationally, residential rates rose about 6.2% year over year.
2025-06 to 2026-05 · cents per kWh
About running a heat pump
A heat pump moves heat rather than generating it, delivering two to four units of heat per unit of electricity. In cold snaps below its balance point it falls back on resistance backup strips, which draw far more - this is why heat pump bills spike in extreme cold rather than scaling smoothly.
What actually changes the cost
- Nameplate wattage is not running cost. This heat pump draws about 2400W when active, but cycles roughly 60% of the time it is switched on, so effective consumption is near 1440W.
- At typical use this is a major load - around 5,256 kWh a year. Efficiency upgrades here pay back faster than on any small appliance.
- Models vary widely, from about 1500W to 4000W. Check the nameplate on your own unit rather than assuming an average, because the spread is more than 2x.
- Insulation and air sealing reduce runtime, which lowers cost more reliably than adjusting the thermostat by a degree.
- If your utility offers time-of-use pricing, shifting this load off-peak can cut its cost substantially without using any less energy.
How we worked this out
The arithmetic is simple and we would rather show it than hide it. Divide watts by 1,000 to get kilowatts, multiply by hours of use and by the duty cycle to get kilowatt-hours, then multiply by your rate:
2400W ÷ 1000 × 10h × 60% = 14.400 kWh/day × 25.40¢ = $3.658 per day
One honest caveat: District of Columbia’s figure is a state average published by the EIA. Your own utility’s tariff, any time-of-use pricing, fixed monthly service charges and local taxes all shift the real number. Put your actual per-kWh rate into the calculator above for a figure that reflects your bill.
Questions about heat pump running costs
How many watts does a heat pump use?
A typical heat pump draws about 2400 watts while running, with most models falling between 1500W and 4000W. Check the nameplate label or manual for your specific unit - the range is wide enough that averages can mislead.
How much electricity does a heat pump use per day?
At around 10 hours of use a day and a 60% duty cycle, that works out to roughly 14.4 kWh per day, or about 432 kWh a month. Your actual figure depends on your usage and model.
Why does the cost differ so much between states?
Residential electricity rates across the US range from about 12.35 cents per kWh in North Dakota to 46.62 cents in Hawaii - nearly a fourfold difference. The same heat pump, used identically, therefore costs almost four times as much to run in the most expensive state as in the cheapest.
Is it cheaper to run a heat pump at night?
Only if you are on a time-of-use or variable tariff. On a flat rate, the time of day makes no difference to cost. If you are on time-of-use pricing, off-peak hours are typically materially cheaper, and shifting this load can reduce its cost without reducing usage.